View CU1216LS_4270131.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

3139 149 12160 1 rev b : 14.01.2005 rf solutions preliminary specification CU1216LS mk3 family all bands dvb-c receiver unit www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 2 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family ordering information type description 12 nc CU1216LS/a gi g v-3 dvb-c, mpeg-2 parallel tr ansport stream; f-long connector, iec connector; active passive loop through, vertical 3139 147 24311 CU1216LS/a gi g h-3 dvb-c, mpeg-2 parallel tr ansport stream; f-long connector, iec connector; active passive loop through, horizontal 3139 147 24321 CU1216LS/a ig g v-3 dvb-c, mpeg-2 parallel transport stream; iec connector, f-long connector; active passive loop through, vertical 3139 147 24331 marking the following items of information are printed on a sticker that is on the top cover of the tuner: ? type number ? code number ? origin letter of factory ? change code ? year and week code features ? small size 40mm x 70mm x 13mm in horizontal mounting ? digitally-controlled (pll) tuning via i 2 c-bus ? minimum power supply : 1.8v, 3.3v and 5v ? fully compliant with ets 300 429 specification for dvb-c application,itu-t j.83 (annex a,b & c) ? output of mpeg-2 parallel/serial transport stream ? digital saw filter ? support up to 256qam ? wide symbol rate of 0.87 to 6.9mbaud ? fulfill cenelec requirements, en55013 & en55020 www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 3 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family description this internal product specification covers cu1216mk2 & cu1216mk3 family . rf electrical characteristic, mechanical interface are the same for both family beside the channel decoder. in the cu1216mk2, the channel decoder used is tda10021. while for the cu1216mk3, the channel decoder used is tda10023. both channel decoders are suppli ed from philips semiconductor. the tda10021 only covers dvb-c requirement while for the tda10023, it covers itu-t j.83 (annex a, b & c) with the dvb-c requirement inclusive. the narrowband 36mhz if output after saw filter is being amplified further by a variable if amplifier. the variable if amplifier having a 60db of dynamic range. t he 2vp-p differential amplified if output is input to a dvb-c receiver. the pre-filter if is also av ailable as if output for analog processing purpose. the CU1216LS mk2/mk3 also allow a passive loop through possib ility beside the active loop through function. upon power down, signals is still available at antenna connector out. dvb-c receiver includes a qam demodulator together with rs forward error correction (8 erroneous bytes correction is possible) and 10bits a/d converter. the output could be either a parallel or a serial mpeg transport stream. intermediate frequencies signal frequency (1) (mhz) center frequency 36.15 notes (1) the oscillator frequency is above the input signal frequency. frequency coverage band frequency range (2) (mhz) low band (3) 51 to 160.25 mid band 160.5 to 444.25 high band 444.5 to 858 (4) notes (2) data refers to the rf channel center frequency (3) sufficient margin is available to tune down to 47mhz. (4) sufficient margin is available to tune up to 866mhz. www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 4 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family block diagram rf out agc vt +5v(lt) mopll ic agc detector pll oscillators passive rf input lt +5v 5v 33v 5v 33v saw if(broadband) if amp if agc error recovery core demodulation pll xtal adc i 2 c i 2 c bus mpeg_ ts_ clk output formatter mpeg_ data_ ena mpeg_ err mpeg ts (d0 ? .d7) /ser +1.8v +3.3v mpeg_ pkt_ sync qam demodulator www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 5 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family definition of terminals / supply data symbol pin description n.c 1 not connected n.c 2 not connected n.c 3 not connected 5v (lt) 4 loop through supply voltage +5v agc 5 automatic gain control (external) +4v [do not connect for normal usage with wideband agc] 5v 6 tuner supply voltage +5v as 7 nim address select vt 8 tuner tuning voltage [for monitoring purpose only, do not connect to power supply] n.c 9 not connected gnd 10 ground 1.8v 11 supply +1.8v 3.3v 12 supply +3.3v if 13 intermediate frequency (unfiltered) gnd 14 ground mpeg d0/ser 15 parallel mpeg transport output data bit 0/serial output mpeg d1 16 parallel mpeg transport output data bit 1 mpeg d2 17 parallel mpeg transport output data bit 2 mpeg d3 18 parallel mpeg transport output data bit 3 mpeg d4 19 parallel mpeg transport output data bit 4 mpeg d5 20 parallel mpeg transport output data bit 5 mpeg d6 21 parallel mpeg transport output data bit 6 mpeg d7 22 parallel mpeg transport output data bit 7 mpeg_ts_clk 23 mpeg transport stream clock sda 24 i 2 c-bus serial data scl 25 i 2 c-bus serial clock rst 26 reset mpeg_data_val 27 mpeg data valid mpeg_pkt_sync 28 mpeg packet sync mpeg_err 29 mpeg error out n.c 30 not connected n.c 31 not connected n.c 32 not connected gnd m1,m2, m3,m4 mounting tags (ground) www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 6 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family limiting values environmental conditions symbol parameter conditions min. max. unit non-operational conditions t amb ambient temperature -25 +85 c rh relative humidity - 95 % g b bump acceleration 25g - 245 m/s 2 g s shock acceleration 50g - 490 m/s 2 vibration amplitude 10 to 55 hz - 0.35 mm operational conditions t amb ambient temperature -10 +60 c rh relative humidity - 95 % limiting values under operational conditions the tuner can be guaranteed to function properly under the following conditions. a) symbol parameter pin min typ. max. unit 5v tuner supply voltage 4.75 5.00 5.50 v v s(ripple) peak to peak ripple voltage susceptibility (6) 5 - - mvpp i 5v supply current 6 - - 150 ma 5v (lt) loop through supply voltage 4.75 5.00 5.25 v i 5v(lt) supply current 4 - - 60 ma 1.8v supply voltage 1.8v 1.75 1.8 1.95 v i 1.8v supply current 11 - - 140 ma 3.3v supply voltage 3.3v 3.0 3.3 3.6 v i 3.3v supply current 12 - - 105 ma v as address select input voltage 7 - - 5.5 v v scl serial clock input voltage 25 -0.3 - 5.5 v v sda serial data input voltage -0.3 - 5.5 v i sda serial data input current 24 -1 - 5 ma note (6) sinusoidal ripple voltage superimposed on the 5v-suppl y voltage in the frequency range of 20 khz to 500 khz. criteria for tv interference is >57 db. www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 7 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family b) power supply sequencing include reset. the voltage level of the 5v must always exceed the voltage level of the 3.3v & 1.8v supply during power up in order to guarantee against latch-up. the voltage level of the 3.3v and 1.8v supplies must alwa ys fit to the following conditions to ensure proper power up conditions if a period of ?t? is needed for 1.8v to turn on, then, 3.3v needs to be turned on after ?t? time of 1.8v. c) reset requirement after power up sequencing, a software reset has to be implemented as follow : this form of reset is managed by host proc essor and the timing conditions as below :- level vih and vil are ttl compliant 3.3v 1.8v 50% tmin 0 www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 8 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family electrical data conditional data unless otherwise specified, all electrical values for chapter ?electrical data? apply at the following conditions and the electrical performance is related to system b,g and h. a proper function is guaranteed within the specified operational conditions but a cert ain deterioration of performance parameters may occur at the limits of operational conditions. symbol parameter value unit t amb ambient temperature 25 2 o c rh relative humidity 60 10 % 5v tuner supply voltage 5 0.1 v 5v(lt) loop through supply voltage 5 0.1 v 1.8v supply voltage 1.8v 1.8 0.1 v 3.3v supply voltage 3.3v 3.3 0.1 v z s(ae) aerial source impedance (unbalanced) 75 ? the tuner has to be tuned to an if-frequency of 36.15 mhz. rf-out must be terminated with 75 ohm when not used! tuner characteristic conditions min. t yp . max. frequency range low band mid band high band 51mhz 164mhz 450mhz 157mhz 442mhz 858mhz tuning margin 3mhz surge protection 4 kv voltage gain CU1216LS (*2) 45db 57db gain taper 6db image rejection low band mid band <300mhz mid band >300mhz high band 0db to 10db gr 66db 66db 63db 50db oscillator phase noise low band mid band high band @10khz -84dbc -84dbc -82dbc rf agc range low band mid band high band 40db 35db 30db 45db noise figure (*3) (*1) 11db osc. voltage at aerial input (75 ? ): (f < 1ghz) (f > 1ghz) < 46dbv < 46dbv www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 9 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family tuner characteristic conditions min. t yp . max. channel tilt (if center 3.0mhz) for CU1216LS (if center 4.0mhz) for CU1216LS 0db gr, f < 300mhz 0db gr, f > 300mhz 4.0db 4.5db loopthrough characteristic (*4) (rf in to rf out ) ? CU1216LS conditions min. typ. max. frequency range 48mhz 855mhz power gain @75 ? -1db 5db noise figure 10db passive lt gain (*4) -2.5db -4db 2 nd order intermodulation 80dbuv input level 136dbuv 3 rd order intermodulation 90dbuv input level 121dbuv 75 ? termination at rf out - freq 70 mhz 6db return loss @75 ? - freq > 70 mhz 8db osc. voltage at rf out: (f < 300mhz) (f > 300mhz) < 20dbv < 30dbv demodulator conditions min. t yp . max. sensitivity 64qam 256qam 6.9ms, ber 2x10 -4 -66dbm -62dbm c/n 64qam 256qam pin = -45dbm, 6.9ms, ber 2x10 -4 26.5 32.5 (*1) : to be measured at broad band if output (*2) : to be measured 3.0mhz from if center. rf-out terminated with 75 ? (*3) : to be measured at max. gain (nom. agc voltage) (*4) : to be measured tuner supply and loop through supply off www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 10 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family application information a detailed description of the iic specification, with applications, is given in brochure ? the iic bus and how to use it?. code number : 9398 393 40011. the cu1216 family contains two i 2 c transceivers, one in the tuner part, and one in the qam channel decoder. it is imperative to ensure that both i 2 c devices are programmed correctly according to their addresses. please note that to prevent interference to the tuner from the constant activity on the i 2 c bus to the channel decoder ic, all i 2 c communications to the mopll ic is gat ed through the decoder ic. in this case, channel decoder?s i 2 c bus should be placed in bypass mode. a more detailed description of the pll ic (especially logi c diagram) can be found in the device specification of philips semiconductor, tda6509ahn. for application information about the channel deco der, please refer to the tda10021/23, single dvb-c channel receiver from philips singapore. code num ber : 9398 393 40011. address select for the module is defined by the tda10021/23 ic on pin 7 (as pin) of the module. if the as pin (pin 7) of the module is grounded, the module?s address is 0 x 18 else if it is tied to 5v, the module address would be 0 x 1a. i 2 c control i 2 c settings (for pll tuner only) logic diagram telegram examples: start - adb ? db1 - db2 - cb - bb - stop start - adb - cb - bb - db1 - db2 - stop start - adb - db1 - db2 - stop start = start condition stop = stop condition adb = address byte db1 = divider byte 1 db2 = divider byte 2 cb = control byte 1 bb = control byte 2 table 1 i 2 c-bus data format, ?write? mode 7 bits 0 name byte msb lsb ack address byte adb 1 1 0 0 0 0 0 r/w=0 a prog. div. byte 1 db1 0 n14 n13 n12 n11 n10 n9 n8 a prog. div. byte 2 db2 n7 n6 n5 n4 n3 n2 n1 n0 a control byte cb 1 cp t2 t1 t0 rsa rsb wsb=0 a band-switch byte bb 0 0 0 p4 p3 p2 p1 p0 a www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 11 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family programmable divider setting (bytes db1 and db2) divider ratio: n = f osc /f ss where f osc = ( f rf + f if ) and f ss is the step-size set by rsa and rsb as described below. n = 8192*n13 + 4096*n12 + 2048*n11 + 1024*n10 + 512*n9 + 256*n8 + 128*n7 + 64*n6 + 32*n5 + 16*n4 + 8*n3 + 4*n2 + 2*n1 + n0 note: f if = 36.15 mhz control byte cb charge pump setting: cp can be set to either 0 (low current) or 1 (high current). cp = 1, charge pump current = 280ua results in fastest tuning (default m ode) cp = 0 , charge pump current = 60ua results in moderate speed tuning with better residual oscillator pll disabling: os=0 for normal operation, os=1 switches off the pll tuning amplifier (pll tuning is disabled) weak signal booster: warning: wsb must be set to 0. otherwise tuner overload will occur . test mode setting: t2 t1 t0 test modes t2 t1 t0 test mode 0 0 0 normal mode (read and write mode bytes allowed) 0 0 1 normal mode (read and write mode bytes allowed) (1) 0 1 0 charge pump is off 0 1 1 byte bb ignored 1 0 0 charge pump sinks current 1 0 1 charge pump sources current 1 1 0 ? f ref output from port p3 1 1 1 ? f ref output from port p3 (1) default mode at power-on reset. reference divider ratio select bits: rsa rsb reference frequency/step size remarks 0 1 31.25khz slow picture search 1 1 62.5khz normal picture search bandswitching byte bb ports p0 p1 p2 p3 p4 low band 1 0 0 0 0 mid band 0 1 0 0 0 high band 0 0 1 0 0 www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 12 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family tuner part programming (read mode) bit allocation (read mode r/w = 1) name msb bit6 bit5 bit4 bit3 bit2 bit1 lsb ack address byte adb 1 1 0 0 0 ma1 ma0 r/w=1 a status byte sb por fl 1 1 1 a2 a1 a0 a the following data can be read from the device through the status byte: por (power on reset) : por is internally set to 1 in case v cc drops below 3v. the por bit is reset when an end of data is detected by the pll-ic. fl: in lock flag (fl = 1 when the phase lock loop is in lock) the loop must be phase-locked during at least 8 periods of the internal 7.8125 khz reference-frequency 1msec before the fl flag is internally set to 1. a2, a1, a0 : not used. www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 13 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family mechanical data see product drawing 3139 149 0155 aerial connections standard phono socket female, iec socket/plug 75 ? or f-connector socket female solderability the solderability of pins and mounting tags when tested initially and after 16 hour steam ageing in accordance with ? iec 60068-2-20 ?, test ta, method 1 (solder bath 235 c for 2s), results in a wetted area of 95%. no de-wetting will occur when soldered at 260 c for 5s. resistance to soldering heat the product will not be damaged when tested in accordance with ? iec 60068-2-20 ?, test tb, ,method 1a (solder bath 260 c for 10 1 s). mass approximately: 41g robustness of pins the pins will not be damaged when tested in accordance with ? iec 60068-2-21 ?: ? test ua1, tensile of 10n in axial direction ? test ua2, thrust of 4n in axial direction punching pattern of chassis pcb for optimum mounting of the tuner to a pcb, the punching pattern is recommended (see 3139 149 0155). the tuner must be mounted without clearance between the tuner supporting surface and the printed circuit board (pcb). when mounted in this way, the tuner must be soldered to the pcb. this can be achieved by pressing the unit vertically onto the pcb during soldering. www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 14 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family packaging info the products are packed in the carton box and tr ansferred to customers by pallet transport. mounting type dimension b x w x h (cm) no. of sets gross wt (kg) carton 46 x 34 x 10.1 108 5.6 horizontal-mount type pallet 120 x 105 x 105 6264 348 carton 46 x 34 x 10.1 128 5.8 vertical-mount type pallet 120 x 105 x 105 7424 362 the information in the above table is valid for the following types only: ? CU1216LS/a f g v-3, ? CU1216LS/a fi g v-3, and ? CU1216LS/a fi g h-3. carton boxes are made of corrugated fibreboard, which are free of environmentally banned substances see product drawing 3139 149 0155 ? page 1 example of carton box: w b h www.datasheet.net/ datasheet pdf - http://www..co.kr/
all bands dvb-c receiver unit CU1216LS mk3 family 3139 149 12160 15 rev b : 14.01.2005 www.datasheet.net/ datasheet pdf - http://www..co.kr/
all bands dvb-c receiver unit CU1216LS mk3 family 3139 149 12160 16 rev b : 14.01.2005 www.datasheet.net/ datasheet pdf - http://www..co.kr/
all bands dvb-c receiver unit CU1216LS mk3 family 3139 149 12160 17 rev b : 14.01.2005 www.datasheet.net/ datasheet pdf - http://www..co.kr/
all bands dvb-c receiver unit CU1216LS mk3 family 3139 149 12160 18 rev b :14.01.2005 www.datasheet.net/ datasheet pdf - http://www..co.kr/
all bands dvb-c receiver unit CU1216LS mk3 family 3139 149 12160 19 rev b :14.01.2005 www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 20 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family document revision history rev # date approved by remarks a 04-12-23 lim kui yong create by james chua b 05-01-14 lim kui yong trigger by joe; pg 10 : updating logic diagram (change from cb1 to cb and cb2 to bb) www.datasheet.net/ datasheet pdf - http://www..co.kr/
philips rf solutions preliminary specification 3139 149 12160 21 rev b : 14.01.2005 all bands dvb-c receiver unit CU1216LS mk3 family definitions data sheet status objective specification this data sheet contains ta rget or goal specifications for product development. preliminary specification this data s heet contains preliminary data; supple mentary data may be published later. product specification this data sheet c ontains final product specification. application information where application information is given, it is ad visory and does not form part of the specification life support applications these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to re sult in personal injury. philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips for any damages resulting from such improper use or sale. purchase of philips i 2 c components rf solutions sales offices refer to : internet : www.rfsolutions.philips.com ? philips electronics n.v. 2004. all rights are reserved. reproduction in whole or in part is pr ohibited without the prior written consent of the copyright owner. the information presented in this document does not fo rm part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication t hereof does not convey nor imply any licens e under patent- or other industrial or intellectual property rights. purchase of philips i 2 c components conveys a license under the philips i 2 c patent to use the components in the i 2 c systems to the i 2 c specification defined by philips. this specification can be ordered using the code 9398 393 40011. www.datasheet.net/ datasheet pdf - http://www..co.kr/

▲Up To Search▲

Price & Availability of CU1216LS

	To Download CU1216LS Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .